Digital Module

This digital input module features 16 channels in a width of just 12 mm (0.47 inch).It receives binary control signals from digital field devices (e.g., sensors, encoders, switches or proximity sensors).The module features Push-in CAGE CLAMP® connections enabling solid conductors to be connected by simply pushing them in.Each input channel has a noise-rejection RC filter with 3.0 ms time constant.A green LED indicates the signal state of each channel.Field and system levels are electrically isolated.An operating tool with a 2.5 mm blade (210-719) is required to open the Push-in CAGE CLAMP® connections.

Digital Module

Number of digital outputs: 16Total number of channels (module): 16Signal type: DigitalSignal type (voltage): 24 VDCActuator connection: 16 x (1-wire)Output characteristics: High-level triggerOutput current per channel: 0.5AOutput current: Short-circuit proofLoad types: Resistive, inductive, lamp loadsMaximum switching frequency: 1 kHzMaximum output data width (internal): 16 bitsSupply voltage (system): 5 VDC; via data contacts

Digital Module

Digital Module

Number of digital outputs: 8Total number of channels (module): 8Signal type: DigitalSignal type (voltage): 24 VDCActuator connection: 8 x (2-wire)Output characteristics: High-level triggerOutput current per channel: 0.5 AOutput current: Short-circuit proofLoad types: Resistive, inductive, lamp loadMaximum switching frequency: 1 kHzMaximum output data width (internal): 8 bitsSupply voltage (system): 5 VDC; via data contactsCurrent consumption (5 V system power supply): 20 mAField-side supply voltage: 24 VDC (-25 … +30%); via power jumper contacts (power supplied via blade contacts; transmission via spring contacts)Current consumption, field-supplied (module without external load): 15 mA

Fieldbus couplers

Fieldbus couplers

Fieldbus couplers

Fieldbus couplers

Communication EtherNet/IP™ETHERNET protocol HTTP(S)BootPDHCPDNSFTP(S)SNMPBaud rate 10/100 MbpsTransmission medium (communication/fieldbus) Twisted pair S-UTP 100 Ω Category 5; M12 D-sub, maximum cable length 100 mTransmission performance Class D, in accordance with EN 50173Maximum number of modules per node 64Maximum number of modules without bus extension 64Configuration options WAGO-I/O-CHECKWeb-based managementCODESYS libraryMaximum input and output process image (fieldbus) 1020 words/1020 wordsSupply voltage (system) 24 VDC; via pluggable connector (CAGE CLAMP®); derating guidelines must be observed!Current consumption (5 V system power supply): 350 mAMaximum system supply current: 1,700 mAField-side supply voltage: 24 VDC; supplied via pluggable connector (CAGE CLAMP®); transmitted via power jumper contacts; derating guidelines must be observed!

Communication: PROFINET IODevice-Specific: Supported protocols: PROFIsafe V2, PROFIenergy V1.0; ID Code: Vendor ID: 0x011D; Device ID: 0x02EE; Module ID: 0x01000177 (firmware versions 01 and 02), 0x02000177 (firmware version 03 and above)PROFINET IO Features: Integrated 2-port switch; Autonegotiation; Auto-MDIX; Isochronous inputs: 1 ms (RT); 1, 2, 4 ms (IRT); Generate/fail programmableBaud rate: 10/100 Mbps (10 Mbps (ETHERNET protocol), 100 Mbps full-duplex communication (PROFINET IO))Maximum bus segment length: 100 mTransmission medium (communication/fieldbus): Twisted-pair S-UTP; 100 Ω; Category 5

Digital Module

Function and Technology Module

Digital Module

Wiring ParametersConnection Technology: Inputs/Outputs: 8 x CAGE CLAMP® (inputs)Connectable Conductor Material: CopperConnection Type: InputSolid Conductor: 0.08 … 2.5 mm² / 28 … 14 AWGFine-Stranded Conductor: 0.08 … 2.5 mm² / 28 … 14 AWGStrip Length: 8 … 9 mm / 0.31 … 0.35 inches

Number of digital inputs: 4Total number of channels (module): 4Signal type: DigitalSignal type (voltage): 24 VAC/DCSensor connections: 2 x (2-wire, 3-wire); When connecting other sensors, an appropriate field-side wiring module (such as the 750-614) must be used.Input characteristics High level trigger Input filter (digital) 50 ms Typical input current 7.5 mA (AC); 9.5 mA (DC) Signal voltage range (0) −3 … +5 VDC; 0 … 5 VAC Signal voltage range (1) 11 … 30 VDC; 10 … 27 VAC Sensor power supply 24 VAC/DC Maximum input data width (internal) 4 bits Supply voltage (system) 5 VDC; via data contacts Current consumption (5 V system power supply) 10 mA Field side supply voltage 24 VAC/DC (-15 … +20 %); via power jumper contacts (power supply via blade contacts; transmission via spring contacts) Isolation 500 V system/field Indicator LED (A-D) Green: DI 1 … DI 4 status

Number of digital inputs: 2Total number of channels (module): 2Signal type: Current loop (intrusion detection)Sensor connection: 2 x (2-wire)Specific sensor properties: Alarm contact: R1 = 1.5 kΩ (±5%); R2 = 2.2 kΩ (±5%); Wire resistance (R-wire): maximum 200 ΩOutput current per channel: 0.001ASensor power supply: 24 VDCMaximum input data width (internal): 4 bitsData width: 4-bit input: 2 bits for data, 2 bits for fault (short circuit/open circuit)Supply voltage (system): 5 VDC; via data contactsCurrent consumption (5 V system power supply): 6 mAField-side supply voltage: 24 VDC (-25 … +30%); via power jumper contacts (power supplied via blade contacts; transmission via spring contacts)Current consumption, field-powered (no external load on module): 16 mAIsolation: 500 V system/field

Number of digital input points 2Total number of channels (module) 2Signal type NAMURSensor connection 2 x (2-wire)Input characteristics High level triggerInput filter (digital) 3msSignal current (0) NAMUR ≤1.2mASignal current (1) NAMUR ≥2.1mAOpen circuit voltage 8.2VShort circuit current ≤ 8.2 mASensor power supply 8.2 VDCSwitching hysteresis 0.2mAInput impedance 1,000ΩInput pulse interval ≥3msAnti-mating protection Short circuit monitoring: > 6.5 mAWire break monitoring: < 0.2 mADiagnostics Short circuit, wire breakMaximum input data width (internal) 4BitData width 4-bit input: 2-bit data, 2-bit fault (short circuit/wire break)

Number of digital inputs 2Total number of channels (modules) 2Signal type DigitalSignal type (voltage) 110 VDCSensor connection 2 x (2-wire)Input characteristics High/Low level trigger, configurableInput filter (digital) 3msSignal (1) Typical input current per channel 2.5mASignal voltage range (0) −14 … +50 VDCSignal voltage range (1) 70 … 143 VDCSensor power supply 110 VDCMaximum input data width (internal) 2BitSupply voltage (system) 5 VDC; via data contactsCurrent consumption (5 V system power supply) 2.5mAField side supply voltage 110 VDC (-20 … +25 %); via power jumper contacts (power supply via knife contacts; transmission via spring contacts)

Digital Module

Intrinsically Safe Module (Ex i)

Analog Module

Number of analog inputs: 4Total number of channels (module): 4Signal type: CurrentSignal type (current): 4 ... 20 mADCSensor connection: 4 x (2-wire)Maximum input voltage: 32 VSignal characteristics: Single-endedResolution: 12 bitsMaximum input impedance: 100 ΩData width: 4 x 16-bit data; 4 x 8-bit control/status (optional)Typical conversion time: 10 msMeasurement error (reference temperature: 25°C)Measurement error, maximum deviation from upper limit: 0.1%

Analog Module

Analog Module

Analog Module

Analog Module

Analog Module